Skip to main content

A New Line of Transceivers ~ DifX

So What Do You Want To Build?

 
 
 
8/7/2017 Mikele, 9A3XZ has provided this video of two rigs he built and enables you to listen to a  Bitx40 and a DifX side by side.
 
 
 
 
 
73's
Pete N6QW


 

8/5/2017 I mentioned a new project in the text of this posting. Shown below  is a before and after photo of V.1 of the 20 Meter Shirt Pocket Transceiver.
 
Updates include:
  1. Full 20 Meter Band Coverage versus only 100 kHz in the original VXO version
  2. USB/LSB front panel selectable
  3. Si5351 and Arduino Nano versus the Crystal Switched Heterodyne VXO
  4. 1/2 inch high OLED versus crude Analog circular dial
  5. Tune Function using a 988 Hz Pulsed Tone (you Bitx guys need one of these)
  6. MOX switch
  7. Homebrew 4.9152 MHs four pole filter --this really beats the Dishal or QER filters. Nice flat response with superb opposite sideband rejection
  8. Smaller than the rig shown on the masthead.
  9. Pout about 2 watts.
73's
Pete N6QW
2017 Updated Version of the 20 Meter Shirt Pocket Transceiver
 
Original Version I of the Shirt Pocket Transceiver

 


Compare the size of the new rig to the D-104 Microphone
 
 
Typically a week doesn't go by where  I receive emails inquiring about projects that I built several (or many) years ago. Much of this traffic is a  result of having posted about 125 You Tube videos and the subject matter of these video will spark a bit of interest which is followed by an email.
 
There was even a video I made on how to keep your feet dry while driving your Jeep Wrangler which suffers from a water intrusion problem. That one video had many hits (like 31,000) and even a few inquiries if I would manufacture the device that fixed the problem.
 
But fundamentally I think there is a desire today to return to our early ham radio roots where if you wanted to get on the air --you were faced with two problems: 1) there were no credit cards (or paypal) and 2) ICOM/Yaseu/Kenwood were yet to be in business. Thus to get on the air --you had to entirely build your own station -- everything was "homebrew". There is just something about the buzz you get when you can say " the rig on this end is homebrew". Which is often followed by "gee it sounds good for a homebrew radio!" Arrgh##$$$$!!!
 
Just yesterday (8/2)  I received an inquiry about the Let's Build Something (LBS) project that appeared in QRP Quarterly several years ago. Basically I was asked to create a special sub-channel on You Tube that collected all of the videos involving the LBS (to make easier for this person to look at all of the videos) and to provide a detailed parts list of all the parts need to build the project. I will do neither of these. If you want to build this project then you have to do some of the work! In fact the one major design criteria for the project was the use of all common parts that were readily available in most junk boxes. One fundamental axiom -- if you want to homebrew then you need a junk box!
 
The best piece of advice I can give if you want to homebrew a rig is to spend $59 and buy the Bitx40 kit from VU2ESE. The $59 gets you a nearly complete rig including being tested and the shipping to your QTH. Your homebrew contribution involves slapping it in a case and making any mods that are available on the Bitx reflector. For $59, you get all the parts, you get a tested board and you even get a digital VFO with LCD readout. Search on hfsigs.com for a link to his site. If you spend another $10 for expedited shipping you can have the kit in less than 3 days. My website has a tutorial on how to actually implement the Bitx40 project.
 
There is a bit of sound advice in this approach as taking on one of my projects for most hams new to home brewing, you simply do not have enough solder burns on your hands. You'll get there in time but there are many fundamental pitfalls to homebrewing a rig such as appears on the masthead. I didn't learn how to do that last week. My very first solid state transceiver was built in the early 1970's.
 
There was a lot of luck in getting that 1970's rig to work. Now today there is less luck involved as evidenced by the second version built just a few months ago. I also spend a lot of time learning about the techniques, processes and technology. That in itself is not a guarantee that everything will work the first time; but at least it gives a leg up on having no grounding in what it takes to build a rig. The very first thing I don't do is heat up the iron and start tack soldering  parts together. I also have learned to be skeptical about claimed results. My recent experience with the Dishal Filter bears testimony to that view.
 
I have a new transceiver on the work bench and this one is not so much new technology but more in the line of repackaging circuits to make a small rig even smaller. For those who have followed some of those 125 You Tube Videos, several years ago I built a 20 Meter Shirt Pocket SSB Transceiver. This new project takes aim at that former project; but with added capabilities in about the same size --yes the 1/2 size OLED display and the Si5351 are part of the mix.
 
Going back to yesterday's LBS email -- that project featured a building block approach where you started first with a direct conversion receiver (DCR) where almost all that was built initially was reused in the upgraded SSB transceiver. The simple idea --get the direct conversion receiver working and then advance to the more difficult sideband transceiver. By the way if you go to http://www.n6qw.com there is a link to the LBS project with all of the detail on how to build one.
 
Many new homebrewer's who undertook the LBS were unsuccessful, I might add, as they simply jumped right into the transceiver part thus bypassing the DCR. When things didn't work they emailed me with "your project sucks" or your design doesn't work. Ultimately those persons finally discovered that they had a wiring error, bad solder joints or failed to apply power to all parts of the circuit. These are rookie mistakes that are only overcome with practice, experience and starting small! It was important to build the DCR first!
 
 
Bill, N2CQR and I in our monthly podcasts (Bill, especially) have advocated building the Michigan Mighty Mite CW transmitter --about 8 parts total -- as a good place to start the home brew Odyssey. Yes even with 8 parts there were many learning failures as evidenced by emails that Bill and I received. But that project is a much better place to start than having limited experience or knowledge and undertaking a 500 part project and then trying to figure out the problem/issue why the board is inoperative.
 
 
But it all comes around to having a solid grounding in the basics before you undertake the complex. At the risk of being politically incorrect, those at the seat of our government should well understand this concept and tenet as applied to governance --and that is not Fake News! This comes back to the Bitx40 -- start there and learn all you can. Then and only then should you undertake an entirely scratch built rig.
 
 
73's
Pete N6QW

Popular posts from this blog

2019 ~ What is the simplest homebrew SSB Transceiver that can be built?

4/27/2019 The Future of our Hobby is Here! Forget those simple rigs with homebrew crystal filters, cranky IRF510's and the analog VFO's. SDR is the wave that is building strength just like a Tsunami. With the Soft Rock V6.3 SMD Version + RRPi2 With the Omnia SDR and RPi2 Pete N6QW How Simple & How Cheap can you  build a Homebrew SSB Transceiver? 4/26/2019 --- I just converted my websites from an obsolete Windows Based Server with GoDaddy to their cPanel (Linux). This was a cost issue as a one year renewal of the Windows Server would buy three years on the cPanel. GoDaddy is discouraging the use of what they call the Obsolete Windows System. So I had to migrate and reload the whole pastapete.com, jessystems.com and the n6qw.com sites to the Linux based servers. Some files and links got lost in the translation --so you might not be able to see everything! Essentially I have  to open every link to verify that it works --that may take some time

New Technology for 2020 ~ The Hermes Lite 2.0 SDR Transceiver

  The Hermes Lite 2.0 SDR Transceiver. November 7th, 2020 ~ It's Settled! It is done! The stain of the Trump era is soon to be removed! Thanks to all who voted. The Voice of the People has been heard.  Congratulations to President Elect Biden and Vice President Elect Harris. Pete N6QW November 3rd, 2020 -- IT WAS THE MOUSE   We all know this is Dump Trump  Day. Go out and vote! It was the mouse! Back in 1999 I stupidly was one of the very first to purchase a Ten Tec Pegasus. Never buy the first batch of a new model.  Touted as the world's first computer controlled radio , actually I think the Kachina 505 was really the first. But the Pegasus was fraught with problems including a trip back to the Smokey Mountains. I was using an older Windows 95 machine to control the Pegasus and that may be a co-conspirator. Well after many calls to TT -- finally someone who has some smarts told me: Fix your station ground, Make all leads short and Buy stock in a ferrite bead company. I did all

The Next Project Updated 10/10/2022! The rubber has hit the pavement!

The Next Project... A 2022 Transceiver. 10/10/2022 My Apologies. It is with regret that I will be terminating any further work on this project. My caregiver duties have over time become a greater time sink and it is almost impossible to build something working only 10-15 minutes at a time spread out over a day. I apologize for not getting it from design ideas to complete hardware. Most likely I have built the last transceiver I will ever build. Thanks for riding along. My website https://www.n6qw.com/  has the pdf of the postings and I will leave this blog page as is. 73's Pete N6QW 10/05/2022 Still Alive! Regrettably my caregiver duties have overtaken any free time so not much progress. But I am hopeful yet this week I will cut at least one board. A PSA from N6QW.  Think of it like Mary Jo has a "crink" in her back and unable to get in the backseat of the 57 VW Beetle. A bit of a setback but not forever.  Seems like the hired caregiver had a small emergency and not able